أين هو فين?
•
لا يوجد رقم تعريف؟
احصل على تقارير إبيكفين
THE WHEEL RIM DIAMETERS ON THESE VEHICLES MAY EXCEED DIMENSIONAL SPECIFICATIONS. THIS MAY CAUSE THE TIRES AND TUBES TO BE OVERSTRESSED DURING MOUNTING OR IMPROPERLY MOUNTED.
THE WHEEL RIM DIAMETERS ON THESE VEHICLES MAY EXCEED DIMENSIONAL SPECIFICATIONS. THIS MAY CAUSE THE TIRES AND TUBES TO BE OVERSTRESSED DURING MOUNTING OR IMPROPERLY MOUNTED.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, "OCCUPANT CRASH PROTECTION", AND 209, "SEAT BELT ASSEMBLIES". THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVER"S SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, "OCCUPANT CRASH PROTECTION", AND 209, "SEAT BELT ASSEMBLIES". THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVER"S SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
BECAUSE OF ITS POSITION, THE WIRING ASSEMBLY MAY CHAFE AGAINST THE COWL-TO-BRAKE PEDAL SUPPORT BRACE WHICH IS LOCATED UNDER THE INSTRUMENT PANEL.
ON THE INVOLVED VEHICLES, BUILD-UP OF CARPET/MAT DEADENER AND INSULATION UNDER THE REAR SEAT FRAME AND SEAT BELT ANCHOR TABS MAY PREVENT THE OPTIONAL FOLDING REAR SEAT CUSHION FROM LATCHING PROPERLY. THE LATCH MAY BE ONLY PARTIALLY ENGAGED AND FAIL TO SUSTAIN THE SEAT BELT ANCHORAGE LOADING REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY AND ANCHORAGES".
THE ENGINE COOLING FAN BLADES MAY CRACK FROM VIBRATIONAL MOTION. BLADE FRAGMENTS MAY SEPARATE WITHOUT PRIOR WARNING FROM A CRACKED BLADE WHILE THE VEHICLE IS IN OPERATION.
BLADES MAY CRACK AND MAY, OVER A PERIOD OF TIME, LOOSEN FROM FAN ASSEMBLY.
ON THE INVOLVED VEHICLES, TEMPERED GLASS MAY HAVE BEEN INSTALLED IN THE REAR DOORS INSTEAD OF LAMINATED GLASS. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 217, "BUS WINDOW RETENTION AND RELEASE". ONE PURPOSE OF THE STANDARD IS TO MINIMIZE THE LIKELIHOOD OF OCCUPANTS BEING EJECTED FROM A BUS IN THE EVENT OF A COLLISION.
ON THE INVOLVED VEHICLES, LEAKAGE MAY OCCUR AT THE THREADED CARBURETOR-TO-FUEL FILTER CONNECTION ON THE SUSPECT CARBURETORS. THIS IS DUE TO AN IMPROPERLY MACHINED CARBURETOR FUEL INLET CONNECTION.
اكتشف نصائح الخبراء والنصائح والأخبار حول شراء المركبات المستعملة وصيانتها.
ماذا يعني أن يكون لديك عنوان سيارة مجدد عند شراء سيارة مستعملة؟ ستجد جميع المع...
اقرأ أكثر
ستخبرك مقالتنا بالتفصيل حيث يمكنك العثور على VIN للسيارة.
اقرأ أكثر
تعرف على كيفية معرفة أفضل المقاييس لمقارنة السيارات
اقرأ أكثر