أين هو فين?
•
لا يوجد رقم تعريف؟
احصل على تقارير إبيكفين
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
IN SOME VEHICLES, THE MANUFACTURER'S PROTECTIVE INTERNAL COATING OF THE ELECTRONIC CRANK ANGLE SENSOR DOES NOT MEET SPECIFICATIONS, WHICH CAN CAUSE AN OPEN CIRCUIT AT HIGH OPERATING TEMPERATURES. THIS CAN CAUSE THE VEHICLE TO STALL.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
LOCK WASHER LOCATED UNDER THE NUT THAT SECURES THE FRONT HUB TO THE DRIVE SHAFT MAY HAVE HAD IMPROPER HEAT TREATMENT AND COULD CRACK.
THE HEATER CONTROL VALVE STEM DOES NOT MEET THE MATERIAL SPECIFICATIONS. HIGH COOLANT TEMPERATURES CAN CAUSE THE STEM TO LEAK.
IF CRUISE CONTROL MAIN SWITCH IS IN THE ON POSITION WHEN ENGINE IS STARTED, SYSTEM CAN BE AFFECTED BY A SHORT DURATION VOLTAGE DROP CAUSED BY OPTIONAL HI-POWER (H340) RADIO.
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
اكتشف نصائح الخبراء والنصائح والأخبار حول شراء المركبات المستعملة وصيانتها.
اقرأ المقال لتعرف كيف يمكنك استرجاع واستعادة مركبتك المسحوبة دون أي مشاكل تذكر
اقرأ أكثر
سنخبرك هنا بكيفية معرفة تفاصيل تسجيل مالك السيارة
اقرأ أكثر
سيخبرك فريقنا بكيفية اختبار قيادة السيارة.
اقرأ أكثر
