أين هو فين?
•
لا يوجد رقم تعريف؟
احصل على تقارير إبيكفين
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
LOCK WASHER LOCATED UNDER THE NUT THAT SECURES THE FRONT HUB TO THE DRIVE SHAFT MAY HAVE HAD IMPROPER HEAT TREATMENT AND COULD CRACK.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE HEATER CONTROL VALVE STEM DOES NOT MEET THE MATERIAL SPECIFICATIONS. HIGH COOLANT TEMPERATURES CAN CAUSE THE STEM TO LEAK.
VEHICLES INVOLVED ARE THOSE THAT HAD THE HEATER VALVE STEMS REPLACED IN AN EARLIER MITSUBISHI RECALL (94V-103.001). CERTAIN VEHICLES HAD AN INCORRECT VALVE STEM INSTALLED WHICH COULD CAUSE THE INCORRECT STEM TO LEAK AFTER A PERIOD OF TIME.
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
THE HEATER CONTROL VALVE STEM DOES NOT MEET THE MATERIAL SPECIFICATIONS. HIGH COOLANT TEMPERATURES CAN CAUSE THE STEM TO LEAK.
اكتشف نصائح الخبراء والنصائح والأخبار حول شراء المركبات المستعملة وصيانتها.
اقرأ هذه المقالة لاكتشاف الكثير من المعلومات حول التأمين الوطني
اقرأ أكثر
تحقق من هذه النصائح المفيدة التي ستساعدك على إطالة عمر المركبة.
اقرأ أكثر
تعرف على كل ما يخص أفخم ماركات وموديلات السيارات لعام 2023.
اقرأ أكثر
