FORD FOCUS Recall Check

Akcja serwisowa nr:

09E012000

Data wycofania:

2009-04-07

Podzespoły:

EXTERIOR LIGHTING

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Akcja serwisowa nr:

00V411000

Data wycofania:

2000-12-12

Podzespoły:

ELECTRICAL SYSTEM: WIRING

VEHICLE DESCRIPTION: PASSENGER VEHICLES. A DECKLID WIRE HARNESS CAN FATIGUE AND DEVELOP BROKEN WIRES IN THE BEND AREA OF THE WIRE HARNESS.

Akcja serwisowa nr:

00V218000

Data wycofania:

2000-08-11

Podzespoły:

STRUCTURE: FRAME AND MEMBERS

VEHICLE DESCRIPTION: PASSENGER VEHICLES. CERTAIN VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FMVSS NO. 201, "OCCUPANT PROTECTION IN INTERIOR IMPACT." THE RESULTANT HIC(D) VALUE AT ONE TARGET LOCATION AP1, LOCATED ON THE TRIM PANEL AT THE JUNCTURE OF THE A-PILLAR AND ROOF SIDE RAIL, MAY BE GREATER THAN DESIGN INTENT.

Akcja serwisowa nr:

06E049000

Data wycofania:

2006-06-05

Podzespoły:

EXTERIOR LIGHTING

CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Akcja serwisowa nr:

00V302000

Data wycofania:

2000-10-24

Podzespoły:

VEHICLE SPEED CONTROL: CABLES

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH SPEED CONTROL AND AUTOMATIC TRANSMISSION. A SPEED CONTROL CABLE COULD HAVE A CORE WIRE THAT IS LONG ENOUGH TO CATCH ON THE SLEEVE AT THE THROTTLE BODY END OF THE CABLE DURING WIDE-OPEN THROTTLE ACCELERATION.

Akcja serwisowa nr:

00V303000

Data wycofania:

2000-10-24

Podzespoły:

WHEELS: LUGS/NUTS/BOLTS/STUDS

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE REAR WHEEL HUB RETAINING NUTS CAN LOOSEN AND ALLOW THE LEFT REAR WHEEL AND BRAKE DRUM ASSEMBLY TO SEPARATE FROM THE VEHICLE.

Akcja serwisowa nr:

09E025000

Data wycofania:

2009-05-11

Podzespoły:

EXTERIOR LIGHTING: HEADLIGHTS

DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Akcja serwisowa nr:

06E026000

Data wycofania:

2006-03-23

Podzespoły:

EXTERIOR LIGHTING

CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Akcja serwisowa nr:

99V346000

Data wycofania:

1999-12-22

Podzespoły:

VEHICLE SPEED CONTROL

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH SPEED CONTROL. THE SPEED CONTROL CABLE END FITTING CAN ALLOW WATER TO ENTER THE SPEED CONTROL SERVO ASSEMBLY. IF THIS OCCURS, CORROSION IN THE SERVO ASSEMBLY COULD DEVELOP AND CAUSE INTERMITTENT SPEED CONTROL OPERATION OR PREVENT THE THROTTLE FROM RETURNING TO IDLE.

Akcja serwisowa nr:

12E007000

Data wycofania:

2012-02-24

Podzespoły:

EQUIPMENT

RIDE CONTROL, LLC (RIDE CONTROL) IS RECALLING CERTAIN READYMOUNT ASSEMBLIES, P/N 746641MT AND 746646MT, WITH CORRESPONDING AFTERMARKET CUSTOMER PART NUMBERS: GABRIEL G56944 AND GABRIEL G56945, AND PRIVATELY BRANDED PARTSMASTER WITH PART NUMBERS G68944 AND G68945. THE READYMOUNT ASSEMBLIES WERE SOLD AS AFTERMARKET SERVICE EQUIPMENT FOR USE ON CERTAIN 2000 THROUGH 2005 FORD FOCUS VEHICLES. THESE ASSEMBLIES WERE ASSEMBLED WITH A NUT WITHOUT THE NECESSARY WASHER. THE ABSENCE OF THE WASHER CAN ALLOW THE READYMOUNT ASSEMBLY TO PULL APART THE TOP MOUNT.