CHRYSLER SEBRING Recall Check

Akcja serwisowa nr:

98V045002

Data wycofania:

1998-03-19

Podzespoły:

VEHICLE SPEED CONTROL

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE DASH PANEL PAD CAN SHIFT INTERFERRING WITH THE THROTTLE CABLE CONTROL.

Akcja serwisowa nr:

98V183000

Data wycofania:

1998-08-17

Podzespoły:

POWER TRAIN: AUTOMATIC TRANSMISSION: PARK/NEUTRAL START INTERLOCK SWITCH

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.

Akcja serwisowa nr:

09E012000

Data wycofania:

2009-04-07

Podzespoły:

EXTERIOR LIGHTING

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Akcja serwisowa nr:

01I012000

Data wycofania:

2002-01-07

Podzespoły:

STEERING: STEERING WHEEL/HANDLE BAR

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1998-1999 CHRYSLER SEBRING JXI LIMITED CONVERTIBLES. THE STEERING COLUMN INTERMEDIATE SHAFT COUPLER PINCH BOLT RETAINING PIN COULD SNAG AND/OR FRAY THE EDGE OF THE DRIVER'S SIDE FLOOR MAT.

Akcja serwisowa nr:

07E055000

Data wycofania:

2007-07-26

Podzespoły:

FUEL SYSTEM, GASOLINE: DELIVERY: FUEL PUMP

CERTAIN AIRTEX FUEL PUMP MODULE ASSEMBLIES, P/N E7081H, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE VEHICLES LISTED ABOVE. THE WALL OF THE FLARED FITTING OF THE FUEL PUMP IS NOT THICK ENOUGH TO PREVENT THE MATING THREADED FITTINGS FROM BOTTOMING OUT BEFORE AN ADEQUATE SEAL IS ACHIEVED. THIS CONDITION MAY RESULT IN LEAKAGE OF FUEL AT THE CONNECTION OF THE VEHICLE FUEL LINE AND THE FUEL PUMP MODULE ASSEMBLY.

Akcja serwisowa nr:

06E091000

Data wycofania:

2006-11-02

Podzespoły:

FUEL SYSTEM, GASOLINE: DELIVERY: FUEL PUMP

CERTAIN AIRTEX FUEL PUMP MODULES, P/NOS. E7089M, E7094M, E7113M, AND E7129M, MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006. THESE FUEL PUMP MODULES WERE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

Akcja serwisowa nr:

06E088000

Data wycofania:

2006-10-26

Podzespoły:

FUEL SYSTEM, GASOLINE: DELIVERY: FUEL PUMP

CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

Akcja serwisowa nr:

02V186000

Data wycofania:

2002-07-23

Podzespoły:

VEHICLE SPEED CONTROL

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH 2.5L V6 ENGINES, THE THROTTLE CONTROL CABLE CAN FRAY CAUSING THE THROTTLE TO BIND OR STICK.

Akcja serwisowa nr:

97V201000

Data wycofania:

1997-11-20

Podzespoły:

SUSPENSION: FRONT: CONTROL ARM: LOWER BALL JOINT

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.

Akcja serwisowa nr:

00V421002

Data wycofania:

2001-03-12

Podzespoły:

SUSPENSION: FRONT: CONTROL ARM: LOWER BALL JOINT

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE RUBBER BOOTS ON THE LOWER LATERAL ARM BALL JOINTS OF THE FRONT SUSPENSION WERE DAMAGED DURING ASSEMBLY, DIRT AND WATER CAN INTRUDE. ALSO, MMC HAS ADDED THE POTENTIAL OF LEAKING MOISTURE, WHICH CAN CAUSE THE BALL STUD TO CORRODE.