¿Dónde el VIN?
•
Sin VIN?
Obtenga reportes de EpicVIN
THE STEEL FUEL RETURN TUBES THAT CONNECT THE FRAME FUEL RETURN LINES WITH THE ENGINE FUEL RAIL CAN CONTACT THE PINCH WELD FLANGE CONNECTING THE DASH PANEL TO THE FLOOR PAN. CONTINUED CONTACT LEADS TO ABRASION OF THE STEEL FUEL RETURN TUBE AND EVENTUALLY RESULTS IN A FUEL LEAK.
THE STEEL FUEL RETURN TUBES THAT CONNECT THE FRAME FUEL RETURN LINES WITH THE ENGINE FUEL RAIL CAN CONTACT THE PINCH WELD FLANGE CONNECTING THE DASH PANEL TO THE FLOOR PAN. CONTINUED CONTACT LEADS TO ABRASION OF THE STEEL FUEL RETURN TUBE AND EVENTUALLY RESULTS IN A FUEL LEAK.
THE STEEL FUEL RETURN TUBES THAT CONNECT THE FRAME FUEL RETURN LINES WITH THE ENGINE FUEL RAIL CAN CONTACT THE PINCH WELD FLANGE CONNECTING THE DASH PANEL TO THE FLOOR PAN. CONTINUED CONTACT LEADS TO ABRASION OF THE STEEL FUEL RETURN TUBE AND EVENTUALLY RESULTS IN A FUEL LEAK.
VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.
WHEN THE AUTOMATIC TRANSMISSION SHIFT LEVER IS PLACED IN THE PARK POSITION, THE PARK PAWL DOES NOT ALWAYS ABUT OR ENGAGE THE PARK GEAR.
BATTERY TO STARTER CABLES ARE LONGER THAN SPECIFIED; EXCESSIVE CABLE LENGTH COULD CONTACT ENGINE DAMPER PULLEY.
THE STEERING GEARS HAVE AN IMPROPERLY MACHINED SNAP RING GROOVE. THIS CAN CAUSE A FRACTURE OF THE SNAP RING WITH SUBSEQUENT DAMAGE TO THE RECIRCULATING BALL GUIDE TUBE. ALSO, THE O-RING SEAL IN VEHICLES BUILT AFTER FEBRUARY 1988 DOES NOT MEET SPECIFICATIONS AND IS INADEQUATE, CAUSING INTERIOR LEAKAGE AROUND THE O-RING / GLIDE RING SEAL IN THE STEERING GEAR.
THE NUTS WHICH HOLD WINDSHIELD WIPER MOTOR TO THE WIPER MODULE MAY NOT HAVE BEEN SUFFICIENTLY TIGHTENED AND MAY LOOSEN OR COME OFF. THIS CAUSES CHANGED WIPER PATTERNS, OR THE WIPERS MAY JAM IF TWO OF THE THREE NUTS COME OFF.
WHEN THE AUTOMATIC TRANSMISSION SHIFT LEVER IS PLACED IN THE PARK POSITION, THE PARK PAWL DOES NOT ALWAYS ABUT OR ENGAGE THE PARK GEAR.
INABILITY TO MAINTAIN PRESSURE IN THE SECONDARY SYSTEM OF THE MASTER CYLINDER (CONTROLS BRAKING OF REAR WHEELS) COULD INCREASE BRAKE PEDAL TRAVEL AND REDUCE BRAKE PERFORMANCE AT TEMPERATURES LESS THAN 40 DEGREES.
Descubra consejos de expertos, sugerencias y noticias sobre la compra y el mantenimiento de vehículos usados.
Continúa leyendo para descubrir algunos consejos perspicaces de conducción seg...
Lea mas
EpicVIN: potenciando los concesionarios con análisis de datos avanzados. Obten...
Lea mas
En este artículo, Usted aprenderá qué pasos puede tomar para mantener el valor...
Lea mas