Vérification de rappel FORD CLUB WAGON

N° de rappel :

78V201000

Date du rappel :

1979-10-12

Composant(s) :

POWER TRAIN: AUTOMATIC TRANSMISSION

THESE TRANSMISSIONS MAY CONTAIN IMPROPERLY MANUFACTURED PARKING PAWL ACTUATING RODS. CONSEQUENTLY, THE UNHARDENED CAM SURFACE OF THESE RODS CAN ALLOW THE ROD TO DEFORM DURING USE WITH RESULTANT INCREASE IN SHIFT EFFORTS AND DIFFICULTY IN RELEASING THE PARKING PAWL AND ENGAGING THE PARKING GEAR.

N° de rappel :

79V153000

Date du rappel :

1979-10-12

Composant(s) :

STRUCTURE: FRAME AND MEMBERS: UNDERBODY SHIELDS

CERTAIN VEHICLES MAY NOT CONTAIN THE SPECIFIED BODY MOUNTED HEAT SHIELDS. THIS COULD CAUSE HIGH FLOOR PAN TEMPERATURES WHEN THE ENGINE IS IDLED FOR EXTENDED PERIODS OF TIME. FOULED SPARK PLUGS OR OTHER ENGINE CONDITIONS COULD FURTHER INCREASE EXHAUST TEMPERATURES.

N° de rappel :

78V269000

Date du rappel :

1979-10-12

Composant(s) :

STEERING: GEAR BOX: SHAFT SECTOR

THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.

N° de rappel :

78V214000

Date du rappel :

1979-10-12

Composant(s) :

SEAT BELTS: REAR/OTHER

ON THE INVOLVED VEHICLES, THE POTENTIAL EXISTS FOR THE OUTBOARD SEAT BELTS TO BECOME TRAPPED IN THE SEAT-BED PIVOTING MECHANISM. SHOULD THE BELT BECOME TRAPPED IN THE MECHANISM WHEN THE SEAT IS CONVERTED TO A BED, THE BELT MAY BECOME CUT OR FRAYED.

N° de rappel :

79V185000

Date du rappel :

1979-10-12

Composant(s) :

WHEELS

THE WHEEL ASSEMBLY MAY CONTAIN SUBSTANDARD WELDS IN THE AREA WHERE THE DISC IS ATTACHED TO THE RIM. AS A RESULT, CRACKS CAN FORM IN THE WHEEL ASSEMBLY, CAUSING AIR LOSS AND AN UNDERINFLATED TIRE.

N° de rappel :

78V256000

Date du rappel :

1979-10-12

Composant(s) :

POWER TRAIN: AUTOMATIC TRANSMISSION

THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN "PARK". AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.

N° de rappel :

77V187000

Date du rappel :

1979-10-12

Composant(s) :

STEERING: LINKAGES: TIE ROD ASSEMBLY

ON THE INVOLVED VEHICLES, THE STEERING TIE ROD AND LINK ASSEMBLIES WITH ADJUSTING SLEEVE CLAMPS MAY HAVE BEEN IMPROPERLY MANUFACTURED. THE CLAMPS CONTAIN A SHARP DIE MARK WHICH COULD CAUSE THE CLAMP TO FRACTURE WHEN THE CLAMP BOLT IS TIGHTENED TO SPECIFICATIONS. THE CLAMP COULD BREAK AND CAUSE SEPARATION OF THE TIE ROD ADJUSTING SLEEVES.

N° de rappel :

77V185000

Date du rappel :

1979-10-12

Composant(s) :

POWER TRAIN: AUTOMATIC TRANSMISSION: LEVER AND LINKAGE: COLUMN SHIFT

ON THE INVOLVED VEHICLES, THE PARK ACTUATION SUPPORT PLATES ARE DEFECTIVE DUE TO THEIR SUSCEPTIBILITY TO CRACKING DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. AS A RESULT, FRAGMENTS FROM A BROKEN PLATE CAN BECOME LODGED IN THE TRANSMISSION PARKING PAWL MECHANISM. THIS COULD PREVENT THE TRANSMISSION PARKING PAWL FROM ENGAGING WHEN THE SELECTOR LEVER IS PLACED IN THE "PARK" POSITION, OR PREVENT THE PAWL FROM BEING DISENGAGED FROM THE PARK GEAR.

N° de rappel :

78V035000

Date du rappel :

1979-10-12

Composant(s) :

POWER TRAIN: AUTOMATIC TRANSMISSION: LEVER AND LINKAGE: COLUMN SHIFT

THE SHIFT SELECTOR REACTION SPRINGS MAY BE DEFORMED AS A RESULT OF IMPROPER INSTALLATION OF SELECTOR LEVERS DURING COLUMN BUILDUP. THUS THE LEVER MAY NOT BE ABLE TO BE MOVED INTO THE INSERT DETENTS LOCATED IN THE STEERING COLUMN ASSEMBLY. THIS COULD PREVENT THE "PARK" GEAR FROM BEING ENGAGED.

N° de rappel :

77V197000

Date du rappel :

1979-10-12

Composant(s) :

VISIBILITY: GLASS, SIDE/REAR

ON THE INVOLVED VEHICLES, TEMPERED GLASS MAY HAVE BEEN INSTALLED IN THE REAR DOORS INSTEAD OF LAMINATED GLASS. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 217, "BUS WINDOW RETENTION AND RELEASE". ONE PURPOSE OF THE STANDARD IS TO MINIMIZE THE LIKELIHOOD OF OCCUPANTS BEING EJECTED FROM A BUS IN THE EVENT OF A COLLISION.