Vehicle Questions and Answers
Welcome to the Vehicle Q&A Hub. Find answers to your automotive questions, share your experiences, and get expert advice on vehicle maintenance, troubleshooting, and more!
How can I reset the anti-theft system on a 2015 Chevrolet Malibu?
15196 views
14 answers
★ Top Answer
To reprogram the anti-theft security system on your 2015 Chevy Malibu, just ensure you have your key accessible. Insert the key into the ignition and wait for about 10 to 15 minutes. Eventually, the anti-theft warning light should disappear. Once the light goes off, you can resume using your vehicle normally. If the problem persists, another option is to disconnect the battery from the vehicle for 20 minutes to reset all settings back to the factory defaults.
More answers
-
I tested both keys and even replaced the starter, battery, and fuse, but it still won't allow me to reset it. Could it be because I've been using the spare key for the car? Do I need to use the main key to reset it instead?
-
Here's a unique paraphrased version of the text:
Hey there, I'm struggling with the process. I've attempted both turning the key, waiting for the car to reset, and disconnecting the positive battery cable for over 30 minutes, but the Security Theft Protection System is still persistent. I'm running out of solutions here. Any other suggestions? -
To reset the anti-theft system on a 2015 Chevy Malibu, try these steps: Turn the ignition key to the On position and wait for about 10 minutes until the flashing anti-theft light turns off. Then, turn the key off, exit the car, and restart it.
-
I left the key turned in the ignition for more than 15 minutes, but the anti-theft alarm never activated. It remained on the entire time.
-
As an American speaker, I would rephrase the steps provided as follows:
1. Start by inserting a correctly cut transponder key into the ignition and turning it to the on position.
2. As soon as you do this, you'll notice the THEFT light coming on. Allow the key to remain in the ON position for about 10 minutes until the light turns off.
3. Within 55 seconds, switch the ignition to the “OFF” position and then back to “ON” for another 10-minute cycle; the THEFT light will stay illuminated during this time.
4. Once the THEFT light goes out again, you will have another window of 55 seconds to turn the ignition to the “OFF” position and then back to “ON.”
5. After the THEFT light goes out for the third time, the key should now be properly programmed.
6. Finally, take out and reinsert the key, then start the vehicle to verify that the programming has been successful. -
I tested those choices but they didn't fix the issue... However, after swapping out the battery in my car key, my car started up smoothly. I hope this solution works for everyone.
-
Turn the key to the off position, use your remote to lock the door, and then start your car. This should solve the issue.
-
When I insert my key, the alarm starts sounding off.
-
I replaced the battery in my key fob and it started right away.
-
I've come across this problem many times, and I've tried all these steps that usually work. However, it continues to occur.
-
The car failed to start, no sounds or movements were observed when attempting to turn it on.
-
Here's a simplified and unique version:
1. Put the transponder key in the ignition and turn it to the on position.
2. The THEFT light will turn on; leave the key in the ON position for 10 minutes until the light goes off.
3. Within 55 seconds, switch the ignition to OFF and then back to ON for another 10 minutes, with the THEFT light staying on.
4. Once the THEFT light goes off again, you have 55 seconds to repeat the OFF to ON step.
5. After the THEFT light turns off for the third time, the key should be programmed.
6. Take out and reinsert the key, start the vehicle to confirm successful programming. -
Were you able to get it to function properly? If yes, how did you do it? (Hopefully you didn't need to bring it to a dealership).
Buying a Used car?
Check it by Epicvin
Check it by Epicvin
