DODGE AVENGER Recall Check

Recall #:

08V152000

Recall Date:

2008-04-02

Component(s):

ELECTRICAL SYSTEM: WIRING

CHRYSLER IS RECALLING 180,963 MY 2007-2008 SEBRING AND DODGE AVENGER VEHICLES EQUIPPED WITH A STANDARD TIRE PRESSURE MONITORING SYSTEM (TPMS). UNUSED ELECTRICAL CONNECTORS FOR THE TPMS MAY BECOME CORRODED AND COULD SHORT CIRCUIT, WHICH CAN CAUSE A VARIETY OF CONDITIONS INCLUDING ENGINE NO-START, DEAD BATTERY, AN INOPERATIVE CRUISE CONTROL OR REMOTE START SYSTEM, AND/OR ENGINE STALLING.

Recall #:

07V104000

Recall Date:

2007-03-15

Component(s):

LATCHES/LOCKS/LINKAGES: DOORS: LATCH

ON CERTAIN PASSENGER VEHICLES, THE FRONT DOOR LATCH CABLE MAY BECOME PARTIALLY UNSEATED FROM THE INTERIOR RELEASE HANDLE HOUSING CAUSING THE DOOR LATCH TO STICK IN THE OPEN POSITION AND NOT BE SECURED TO THE STRIKER.

Recall #:

07V473000

Recall Date:

2007-10-10

Component(s):

ENGINE AND ENGINE COOLING: COOLING SYSTEM: RADIATOR ASSEMBLY

ON CERTAIN VEHICLES EQUIPPED WITH 2.4 LITER ENGINES, THE ENGINE COOLANT MAY BE DRAWN INTO THE LEFT RADIATOR COOLING FAN MOTOR CONNECTOR.

Recall #:

09E025000

Recall Date:

2009-05-11

Component(s):

EXTERIOR LIGHTING: HEADLIGHTS

DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Recall #:

00V421002

Recall Date:

2001-03-12

Component(s):

SUSPENSION: FRONT: CONTROL ARM: LOWER BALL JOINT

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE RUBBER BOOTS ON THE LOWER LATERAL ARM BALL JOINTS OF THE FRONT SUSPENSION WERE DAMAGED DURING ASSEMBLY, DIRT AND WATER CAN INTRUDE. ALSO, MMC HAS ADDED THE POTENTIAL OF LEAKING MOISTURE, WHICH CAN CAUSE THE BALL STUD TO CORRODE.

Recall #:

06E064000

Recall Date:

2006-07-17

Component(s):

EXTERIOR LIGHTING

CERTAIN TRADESONIC COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Recall #:

09E012000

Recall Date:

2009-04-07

Component(s):

EXTERIOR LIGHTING

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Recall #:

07E055000

Recall Date:

2007-07-26

Component(s):

FUEL SYSTEM, GASOLINE: DELIVERY: FUEL PUMP

CERTAIN AIRTEX FUEL PUMP MODULE ASSEMBLIES, P/N E7081H, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE VEHICLES LISTED ABOVE. THE WALL OF THE FLARED FITTING OF THE FUEL PUMP IS NOT THICK ENOUGH TO PREVENT THE MATING THREADED FITTINGS FROM BOTTOMING OUT BEFORE AN ADEQUATE SEAL IS ACHIEVED. THIS CONDITION MAY RESULT IN LEAKAGE OF FUEL AT THE CONNECTION OF THE VEHICLE FUEL LINE AND THE FUEL PUMP MODULE ASSEMBLY.

Recall #:

09E025000

Recall Date:

2009-05-11

Component(s):

EXTERIOR LIGHTING: HEADLIGHTS

DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Recall #:

00V421002

Recall Date:

2001-03-12

Component(s):

SUSPENSION: FRONT: CONTROL ARM: LOWER BALL JOINT

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE RUBBER BOOTS ON THE LOWER LATERAL ARM BALL JOINTS OF THE FRONT SUSPENSION WERE DAMAGED DURING ASSEMBLY, DIRT AND WATER CAN INTRUDE. ALSO, MMC HAS ADDED THE POTENTIAL OF LEAKING MOISTURE, WHICH CAN CAUSE THE BALL STUD TO CORRODE.