FORD Recall Check

Recall #:

82V119000

Recall Date:

1982-12-13

Component(s):

VEHICLE SPEED CONTROL: CABLES

THESE VEHICLES MAY HAVE BEEN MANUFACTURED WITH AN INCORRECT END CLAMP ON THE HAND THROTTLE ACTUATING CABLE. UNDER CERTAIN CONDITIONS, PERTAINING TO THE CLAMP-TO-THROTTLE CABLE ORIENTATION AND DISTANCES OF THE CABLE TO GOVERNOR SHAFT, THE THROTTLE CABLE END CLAMP MAY INTERFERE WITH THE OUTBOARD ACCELERATOR.

Recall #:

82V120000

Recall Date:

1982-12-13

Component(s):

SERVICE BRAKES, HYDRAULIC: FOUNDATION COMPONENTS: HOSES, LINES/PIPING, AND FITTINGS

THE BRAKE MASTER CYLINDER TO CHASSIS TUBE AND HOSE ASSEMBLY MAY HAVE BEEN LOCATED IN SUCH A WAY THAT IT IS SUSCEPTIBLE TO CHAFING DURING VEHICLE OPERATION. CONTINUED CHAFING MAY RESULT IN TUBE OR HOSE FAILURE AND SUBSEQUENT LOSS OF BRAKE FLUID.

Recall #:

82V120000

Recall Date:

1982-12-13

Component(s):

SERVICE BRAKES, HYDRAULIC: FOUNDATION COMPONENTS: HOSES, LINES/PIPING, AND FITTINGS

THE BRAKE MASTER CYLINDER TO CHASSIS TUBE AND HOSE ASSEMBLY MAY HAVE BEEN LOCATED IN SUCH A WAY THAT IT IS SUSCEPTIBLE TO CHAFING DURING VEHICLE OPERATION. CONTINUED CHAFING MAY RESULT IN TUBE OR HOSE FAILURE AND SUBSEQUENT LOSS OF BRAKE FLUID.

Recall #:

80V133000

Recall Date:

1980-12-09

Component(s):

ELECTRICAL SYSTEM: WIRING: FRONT UNDERHOOD

SOME OF THE INVOLVED VEHICLES WERE PRODUCED WITH AN ENGINE COMPARTMENT WIRE ASSEMBLY THAT MAY HAVE BEEN ROUTED ABOVE THE AIR CONDITIONING SUCTION HOSE. THIS HOSE MAY PUSH UP ON THE WIRING HARNESS CAUSING IT TO CONTACT THE HOOD PROP ROD BRACKET ATTACHING BOLT. THIS COULD LEAD TO PENETRATION OR CHAFING OF THE WIRING INSULATION.

Recall #:

83V013000

Recall Date:

1983-02-23

Component(s):

SEAT BELTS

THE PORTION OF THE ROOF ABOVE FRAME (RAIL) TO WHICH THE SHOULDER BELT IS ANCHORED MAY HAVE A SLOT THAT CAN COMPROMISE THE STRENGTH OF THE SHOULDER BELT ANCHOR UNDER CERTAIN SEVERE LOADS. (THE SUSPECT AREA IS NOT VISIBLE.) CONSEQUENTLY, SOME VEHICLES INCLUDED IN THIS RECALL MAY NOT MEET THE 3000 POUND ANCHORAGE STRENGTH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 210, "SEAT BELT ASSEMBLY ANCHORAGES".

Recall #:

84V034000

Recall Date:

1984-04-05

Component(s):

FUEL SYSTEM, GASOLINE: STORAGE: TANK ASSEMBLY: MOUNTING

ATTACHING BOLTS ON FUEL TANK SUPPORTS MAY NOT HAVE BEEN ADEQUATELY TIGHTENED; ALSO, THE SUPPORTS ARE TOO THIN. HIGH LEVELS OF STRESS, WHICH COULD OCCUR UNDER NORMAL OPERATING CONDITIONS, COULD CAUSE CRACKS TO DEVELOP IN THE SUPPORT STRAPS. IF THE FUEL TANK SUPPORTS FRACTURE, THE FUEL TANK WILL SLIP FROM THE NORMAL POSITION, AND FUEL LEAKAGE COULD RESULT.

Recall #:

07E064000

Recall Date:

2007-08-24

Component(s):

FUEL SYSTEM, GASOLINE: DELIVERY: FUEL PUMP

CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

Recall #:

07E064000

Recall Date:

2007-08-24

Component(s):

FUEL SYSTEM, GASOLINE: DELIVERY: FUEL PUMP

CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

Recall #:

81V124000

Recall Date:

1981-10-28

Component(s):

SERVICE BRAKES, HYDRAULIC: FOUNDATION COMPONENTS: HOSES, LINES/PIPING, AND FITTINGS

THE MASTER CYLINDER TO CHASIS BRAKE TUBE AND HOSE ASSEMBLIES MAY HAVE BEEN MOVED FROM THEIR INTENDED POSITION, WHICH COULD ALLOW CHAFING AGAINST UNDERBODY COMPONENTS. CHAFING PROMOTES WEAR OF THE BRAKE TUBE AND HOSE ASSEMBLY AND COULD CAUSE A LOSS OF BRAKE FLUID.

Recall #:

81V124000

Recall Date:

1981-10-28

Component(s):

SERVICE BRAKES, HYDRAULIC: FOUNDATION COMPONENTS: HOSES, LINES/PIPING, AND FITTINGS

THE MASTER CYLINDER TO CHASIS BRAKE TUBE AND HOSE ASSEMBLIES MAY HAVE BEEN MOVED FROM THEIR INTENDED POSITION, WHICH COULD ALLOW CHAFING AGAINST UNDERBODY COMPONENTS. CHAFING PROMOTES WEAR OF THE BRAKE TUBE AND HOSE ASSEMBLY AND COULD CAUSE A LOSS OF BRAKE FLUID.