CHEVROLET Recall Check

Recall #:

81V104000

Recall Date:

1981-09-17

Component(s):

STEERING: STEERING WHEEL/HANDLE BAR

DURING ASSEMBLY THE UPPER STEERING COLUMN SHAFT PINCH BOLT MAY NOT HAVE BEEN SUFFICIENTLY TIGHTENED. MOVEMENT MAY OCCUR BETWEEN THE UPPER STEERING SHAFT AND THE YOKE, CAUSING ACCELERATED PINCH BOLT WEAR AT THE "WHISTLE SLOT" IN THE SHAFT. PINCH BOLT WEAR COULD CAUSE THE YOKE TO SLIP FROM THE SHAFT.

Recall #:

80V150000

Recall Date:

1980-12-17

Component(s):

SERVICE BRAKES, HYDRAULIC: PEDALS AND LINKAGES

THE INVOLVED VEHICLES MAY HAVE BEEN ASSEMBLED WITHOUT THE RETAINER CLIP FOR THE BRAKE PEDAL PUSH ROD. THE ABSENCE OF THIS RETAINER CLIP COULD ALLOW THE BRAKE PEDAL TO DISENGAGE FROM THE MASTER CYCLINDER PUSH ROD.

Recall #:

80V125000

Recall Date:

1980-12-10

Component(s):

SERVICE BRAKES, HYDRAULIC: PEDALS AND LINKAGES

THE INVOLVED VEHICLES MAY HAVE BEEN ASSEMBLED WITH A BRAKE PEDAL SUPPORT BRACKET WHICH WAS DESIGNED FOR USE IN DIESEL ENGINE VEHICLES. THE INCORRECT BRACKET MAY CAUSE THE SERVICE BRAKES TO REMAIN PARTIALLY APPLIED, RESULTING IN BRAKE OVERHEATING AND REDUCED BRAKING EFFECTIVENESS.

Recall #:

80V150000

Recall Date:

1980-12-17

Component(s):

SERVICE BRAKES, HYDRAULIC: PEDALS AND LINKAGES

THE INVOLVED VEHICLES MAY HAVE BEEN ASSEMBLED WITHOUT THE RETAINER CLIP FOR THE BRAKE PEDAL PUSH ROD. THE ABSENCE OF THIS RETAINER CLIP COULD ALLOW THE BRAKE PEDAL TO DISENGAGE FROM THE MASTER CYCLINDER PUSH ROD.

Recall #:

80V150000

Recall Date:

1980-12-17

Component(s):

SERVICE BRAKES, HYDRAULIC: PEDALS AND LINKAGES

THE INVOLVED VEHICLES MAY HAVE BEEN ASSEMBLED WITHOUT THE RETAINER CLIP FOR THE BRAKE PEDAL PUSH ROD. THE ABSENCE OF THIS RETAINER CLIP COULD ALLOW THE BRAKE PEDAL TO DISENGAGE FROM THE MASTER CYCLINDER PUSH ROD.

Recall #:

80V125000

Recall Date:

1980-12-10

Component(s):

SERVICE BRAKES, HYDRAULIC: PEDALS AND LINKAGES

THE INVOLVED VEHICLES MAY HAVE BEEN ASSEMBLED WITH A BRAKE PEDAL SUPPORT BRACKET WHICH WAS DESIGNED FOR USE IN DIESEL ENGINE VEHICLES. THE INCORRECT BRACKET MAY CAUSE THE SERVICE BRAKES TO REMAIN PARTIALLY APPLIED, RESULTING IN BRAKE OVERHEATING AND REDUCED BRAKING EFFECTIVENESS.

Recall #:

07E088000

Recall Date:

2007-10-30

Component(s):

EQUIPMENT

CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.

Recall #:

80V150000

Recall Date:

1980-12-17

Component(s):

SERVICE BRAKES, HYDRAULIC: PEDALS AND LINKAGES

THE INVOLVED VEHICLES MAY HAVE BEEN ASSEMBLED WITHOUT THE RETAINER CLIP FOR THE BRAKE PEDAL PUSH ROD. THE ABSENCE OF THIS RETAINER CLIP COULD ALLOW THE BRAKE PEDAL TO DISENGAGE FROM THE MASTER CYCLINDER PUSH ROD.

Recall #:

07E088000

Recall Date:

2007-10-30

Component(s):

EQUIPMENT

CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.

Recall #:

83V077000

Recall Date:

1983-09-06

Component(s):

VEHICLE SPEED CONTROL: CABLES

ACCELERATOR PUMP LEVER RETAINING PIN MAY LOOSEN AFTER REPEATED HEAVY ACCELERATOR PEDAL APPLICATIONS. THIS COULD CAUSE THE THROTTLE TO BECOME STUCK IN THE OPEN POSITION.