FORD Recall Check

Recall #:

78V256000

Recall Date:

1979-10-12

Component(s):

POWER TRAIN: AUTOMATIC TRANSMISSION

THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN "PARK". AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.

Recall #:

78V256000

Recall Date:

1979-10-12

Component(s):

POWER TRAIN: AUTOMATIC TRANSMISSION

THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN "PARK". AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.

Recall #:

77V220000

Recall Date:

1979-10-12

Component(s):

EQUIPMENT: APPLIANCE: AIR CONDITIONER

THE INVOLVED VEHICLES MAY CONTAIN AIR CONDITIONERS WHICH HAVE BLOWER MOTOR RESISTOR WIRES WHICH WERE IMPROPERLY ROUTED TOO CLOSE TO THE BLOWER HOUSING WALL. AS A RESULT, THE BLOWER MOTOR COULD BECOME JAMMED AND, IF THE BLOWER SWITCH IS IN EITHER THE MEDIUM OR LOW POSITION, THE POLYPROPYLENE BLOWER HOUSING COULD IGNITE.

Recall #:

77V221000

Recall Date:

1979-10-12

Component(s):

EQUIPMENT: APPLIANCE: AIR CONDITIONER

THE INVOLVED VEHICLES ARE EQUIPPED WITH AIR CONDITIONING UNITS WHICH CONTAIN BLOWER MOTOR RESISTOR WIRES WHICH ARE IMPROPERLY POSITIONED. AS A RESULT, UNDER CERTAIN CONDITIONS THE POLYPROPYLENE CASE MATERIAL COULD BECOME OVERHEATED AND EVENTUALLY IGNITE, ESPECIALLY IF THE BLOWER MOTOR SWITCH IS IN THE LOW OR MEDIUM POSITION.

Recall #:

77V196000

Recall Date:

1979-10-12

Component(s):

VEHICLE SPEED CONTROL: CABLES

THE DUST TUBE PORTION OF THE ACCELERATOR CABLE ASSEMBLY ON THE INVOLVED VEHICLES MAY BIND DUE TO IMPROPER CRIMPING OF THE CABLE ASSEMBLY DURING MANUFACTURE. AS A RESULT, THE RETURN RATE OF THE THROTTLE MAY BE SLOWED OR THE THROTTLE MAY BE PREVENTED FROM CLOSING PROPERLY. IN THIS CONDITION, A VEHICLE SPEED OF 30 T0 40 MPH COULD BE MAINTAINED WITHOUT DEPRESSING THE ACCELERATOR PEDAL.

Recall #:

07E064000

Recall Date:

2007-08-24

Component(s):

FUEL SYSTEM, GASOLINE: DELIVERY: FUEL PUMP

CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

Recall #:

07E064000

Recall Date:

2007-08-24

Component(s):

FUEL SYSTEM, GASOLINE: DELIVERY: FUEL PUMP

CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

Recall #:

81V003000

Recall Date:

1981-02-12

Component(s):

ENGINE AND ENGINE COOLING: COOLING SYSTEM: FAN

THE SEVEN-BLADE ENGINE COOLING FAN IS SUBJECT TO FATIGUE CRACKING DURING NORMAL OPERATION. PORTIONS OF THE BLADES MAY SEPARATE WITHOUT PRIOR WARNING.

Recall #:

77V187000

Recall Date:

1979-10-12

Component(s):

STEERING: LINKAGES: TIE ROD ASSEMBLY

ON THE INVOLVED VEHICLES, THE STEERING TIE ROD AND LINK ASSEMBLIES WITH ADJUSTING SLEEVE CLAMPS MAY HAVE BEEN IMPROPERLY MANUFACTURED. THE CLAMPS CONTAIN A SHARP DIE MARK WHICH COULD CAUSE THE CLAMP TO FRACTURE WHEN THE CLAMP BOLT IS TIGHTENED TO SPECIFICATIONS. THE CLAMP COULD BREAK AND CAUSE SEPARATION OF THE TIE ROD ADJUSTING SLEEVES.

Recall #:

77V187000

Recall Date:

1979-10-12

Component(s):

STEERING: LINKAGES: TIE ROD ASSEMBLY

ON THE INVOLVED VEHICLES, THE STEERING TIE ROD AND LINK ASSEMBLIES WITH ADJUSTING SLEEVE CLAMPS MAY HAVE BEEN IMPROPERLY MANUFACTURED. THE CLAMPS CONTAIN A SHARP DIE MARK WHICH COULD CAUSE THE CLAMP TO FRACTURE WHEN THE CLAMP BOLT IS TIGHTENED TO SPECIFICATIONS. THE CLAMP COULD BREAK AND CAUSE SEPARATION OF THE TIE ROD ADJUSTING SLEEVES.